[WIP] Jönköpingsbanan

[Pinocchio]

Ursprungligen postat av Totte

Hello!
These are the tracks that require the Altenburg to Vildau route.
Download here: https://rail-sim.de/forum/filebase/e...wildau-v-3-12/

Hope you get to see the tracks!

By the way, do you have/possess this landscape/scenery object add-on: Renault Kangoo v1.0 for Jönköpingsbanan v 1.0 route add-on of Railworks/TrainSimulator Classic program? The original download address link has expired already, and I can't find more available address links anyway at present. So I beg you: If you have/possess this landscape/scenery object add-on on your PCs, can you provide/leave me this landscape/scenery object add-on here? If this is the case, it would be great. Thank you very much, thanks a lot for your great assistance, and all my best wishes/greetings to you! Take care. Good luck

[Hgv]

Rutten fungerar i 32 bit om man installerar och kör en äldre version av TS. Jag följde instruktionerna i länken nedan och kopierade över Assets och Content till den "nya" installationen.

The route works in 32 bit if you install and run an older version of TS. I followed the instructions in the link below and copied Assets and Content to the "new" installation.


https://forums.dovetailgames.com/thr...-to-tsc.71041/

[Tarik Pasic]

Ursprungligen postat av Hgv

Rutten fungerar i 32 bit om man installerar och kör en äldre version av TS. Jag följde instruktionerna i länken nedan och kopierade över Assets och Content till den "nya" installationen.

The route works in 32 bit if you install and run an older version of TS. I followed the instructions in the link below and copied Assets and Content to the "new" installation.


https://forums.dovetailgames.com/thr...-to-tsc.71041/

In my case, the old Jonkopingsbanan route works fine in 32 bits but the newer Jonkopinsbanan from 2020 doesn't work at alll... Are you still working on this route?

[Hgv]

I'm no longer working on the route as it's not working in the later versions of TS. I've been trying to figure out why exactly this is; I understand it's a problem with signal scripts so perhaps it's possible to clean up the scripts, but my knowledge is too limited. I posted about it here: https://forums.dovetailgames.com/thr...updates.82307/

As mentioned above, you can get the latest version of the route to work if you install an older version of TS. This can be kept in a separate location in case you want the current TS version as well.

[Tarik Pasic]

Ok fair enough, that's really unfortunate, there's been a lot of problem on Swedish routes due to 32 bits versus 64 bits and now apparently signals and scripts too... Have you tried to talk to DTG management about this? Do you have a picutre of the route version from 2020? I want to see if it's the same version as the old (original) Jonkopingsbanan from Banbyggarna.

[Hgv]

This is the latest version: http://www.e-buzz.se/forum/showpost....5&postcount=25

The one on Banbyggarna is a very old version. It may be that this version works as it's a lot less complex with less signalling and it doesn't include any of the layout around Stockholm which I have included in the later versions (in hindsight that should probably have been a separate route...).

I would suggest if you want to run the route to make a separate installation of an older TS version as explained previously. Alternatively you can try to disable certain signals, but you may still run into problems e.g. when a train activates a crossing signal. With the old TS version the signals should work predictably with no crashes.

In the DTG forums I have tried to raise the issue of scripts causing crashes in the later TS versions but I haven't received any official response. I'm not sure if there is another way to contact DTG about it.

[Tarik Pasic]

Ursprungligen postat av Hgv

This is the latest version: http://www.e-buzz.se/forum/showpost....5&postcount=25

The one on Banbyggarna is a very old version. It may be that this version works as it's a lot less complex with less signalling and it doesn't include any of the layout around Stockholm which I have included in the later versions (in hindsight that should probably have been a separate route...).

I would suggest if you want to run the route to make a separate installation of an older TS version as explained previously. Alternatively you can try to disable certain signals, but you may still run into problems e.g. when a train activates a crossing signal. With the old TS version the signals should work predictably with no crashes.

In the DTG forums I have tried to raise the issue of scripts causing crashes in the later TS versions but I haven't received any official response. I'm not sure if there is another way to contact DTG about it.

Yes I've been trying to work with that 2020 version, unfortunately your 2019 versions are no longer available (maybe they would work without any signals or scripts issues). Unfortunately, when I delete the signals and scripts, I am able to access the route BUT I only get the Stockholm area portion of the route and not the Jonkopingsbanan part, for some reason. I like the version on Banbyggarna but it's indeed very old and also quite short ("only" 23 kilometers). Is your version of the route longer? Do you happen to have a 3D map somewhere maybe?

When it comes to other forums, I know a guy who is very good at fixing issues on route. Unfortunately, I recently had him fix something for me so I don't necessarily feel comfortable asking him for help again so quickly but let's see, I can talk to him about your route eventually if you want.