IORE + T46-GPC + Dm3 "modern" + Fammoorr050 - Donationware - Svenska 3D-Tåg

Hawk · 2017-06-28, 19:24

Jag skickade detta PM långt före dig den 22-6

Akki · 2017-06-29, 07:37

OK

Åke

Hawk · 2017-06-29, 23:00

10 tecken....

PatrikF1 · 2017-07-28, 14:02

Thanks, have donated now might update after i have gotten it working.

Hgv · 2021-03-03, 23:09

Not sure which thread to post this in, but I have a problem whenever I have a long player train with the Fammoorr wagons. If the train is longer than about 25 wagons, it "jumps" at the start of the scenario causing some wagons to derail (see picture).

It seems the only workaround is to use shorter trains, or to connect more wagons to the player train after starting the scenario. For example, if I start with 28 wagons, and connect another 20, and then another 20, it seems I don't get the derailment. That seems to be the only way for the player to run full length trains (68 wagons).

This problem appears to affect the player train only - AI trains are running fine. I suppose it's because TS handles the player train physics differently from AI trains.

Yellow_wing · 2021-03-04, 10:27

Hello HGV

I have no experience with this route and the IORE locomotive. I have ordered them and hope I could drive it soo.

Question: Which Train Simulator version do you use?

In real life, a maximum of 68 cars are attached. But sometimes there are shorter trains (only 40 cars or less). Generally the ore trains are allowed to drive max. 50 km/h. Does this also happen at the reduced speed?
Sure, these trains must be driven with extreme fine comands (not so easy). And of course too, the program can only simulate this very roughly.

I would be interested about your feedback, thank you!

Greetings from Switzerland
Yellow

Hgv · 2021-03-04, 12:05

I use the 32 bit version normally.

What happens when a scenario is loaded when you start it, or whenever a player train approaches a consist, is that this consist "jumps". You can see this if you create a scenario where you put a player loco some distance away from a number of wagons. As you approach the wagons, at a distance of maybe 15-30 m, if you look closely you will see the wagons "jump". Apparently if it's a large number of wagons it can cause them to derail. To be clear: It doesn't need the player loco to even touch the wagons for them to "jump" like this.

I assume this behaviour is because for player trains the physics are more complex than for AI trains. (I think for AI trains the sim basically just moves around the 3D objects at the set speed, but for the player train it takes into account the weight of the wagons, the track gradient and so on.)

What I'd like to know is if there's a way to fix this, perhaps some adjustment that newS can make to the wagon simulation. It would be nice to be able to drive full length trains.

2017-06-28, 19:24	#1
Hawk Veteran Reg.datum: Aug 2001 Ort: Mölndal Inlägg: 4 267	Jag skickade detta PM långt före dig den 22-6 __________________

2017-06-29, 23:00	#3
Hawk Veteran Reg.datum: Aug 2001 Ort: Mölndal Inlägg: 4 267	. 10 tecken.... __________________ Senast redigerad av Hawk den 2017-06-29 klockan 23:19.

2017-07-28, 14:02	#4
PatrikF1 Medlem Reg.datum: Feb 2017 Ort: Sweden Inlägg: 4	Thanks, have donated now might update after i have gotten it working. Senast redigerad av PatrikF1 den 2017-07-28 klockan 16:32.

2017-06-29, 07:37	#2
Akki Medlem Reg.datum: Dec 2012 Ort: Helsingborg, Sweden Inlägg: 186	OK Åke

2021-03-04, 10:27	#6
Yellow_wing Medlem Reg.datum: Oct 2012 Ort: Switzerland Inlägg: 12	Hello HGV I have no experience with this route and the IORE locomotive. I have ordered them and hope I could drive it soo. Question: Which Train Simulator version do you use? In real life, a maximum of 68 cars are attached. But sometimes there are shorter trains (only 40 cars or less). Generally the ore trains are allowed to drive max. 50 km/h. Does this also happen at the reduced speed? Sure, these trains must be driven with extreme fine comands (not so easy). And of course too, the program can only simulate this very roughly. I would be interested about your feedback, thank you! Greetings from Switzerland Yellow

2021-03-04, 12:05	#7
Hgv Medlem Reg.datum: Apr 2007 Inlägg: 817	I use the 32 bit version normally. What happens when a scenario is loaded when you start it, or whenever a player train approaches a consist, is that this consist "jumps". You can see this if you create a scenario where you put a player loco some distance away from a number of wagons. As you approach the wagons, at a distance of maybe 15-30 m, if you look closely you will see the wagons "jump". Apparently if it's a large number of wagons it can cause them to derail. To be clear: It doesn't need the player loco to even touch the wagons for them to "jump" like this. I assume this behaviour is because for player trains the physics are more complex than for AI trains. (I think for AI trains the sim basically just moves around the 3D objects at the set speed, but for the player train it takes into account the weight of the wagons, the track gradient and so on.) What I'd like to know is if there's a way to fix this, perhaps some adjustment that newS can make to the wagon simulation. It would be nice to be able to drive full length trains.