Svenska 3D-Tåg - Forum  
 

If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

Go Back   Svenska 3D-Tåg - Forum > N3V Trainz > Trainz - Allmänt om Trainz

Reply
 
Thread Tools Display Modes
Old 07-16-2010, 09:56 PM   #1
hgkn
Medlem
 
Join Date: Mar 2003
Location: Kista, Sweden.
Posts: 763
Unhappy WaitForTrigger

Kan inte få WaitForTrigger Driver Command att fungera i 2010 vilket gör mig besviken då det är ett väldigt användbart komando. Så här lyder Description:

A Driver Command that allows you to tell a driver to wait until
a Trigger is triggered by a train.

Manual:
To use this command you need to add it in your sessions Driver Command Setup Rule.

Right Click on the Driver itself or the Loco with the Driver, and select Wait For Trigger.
The next Step is to choose which trigger you want to wait for, and then which train should
trigger the Trigger you selected. You can also select Any Train, so the first train that
triggers the Trigger fullfills the command.

The Trains are identified by their leading locomotive. In the menu you will only see Trains that have
a locomotive. If a consist that has no locomotive comes across the selected Trigger nothing will
happen too.

Please be carefull that you do not give two Triggers the same name. You will see them
both in the Menu, but just one of them will work (trigger), and you would have to try
which one, and it might not allways be the same. So better make sure every trigger has an
unique name.

Någon som har en lösning?
__________________
hgkn@bahnhof.se
hgkn besöker inte forumet just nu  
Reply With Quote
Old 07-17-2010, 08:53 AM   #2
korvtiger
Medlem
 
Join Date: Jan 2008
Location: Uppland, Sverige
Posts: 2,728
Default

Testade lite snabbt i TS2010 SP2 och det funkar lika utmärkt som alltid. Kan du beskriva vad du testat lite närmare?
__________________
-k-
korvtiger besöker inte forumet just nu   Reply With Quote
Old 07-17-2010, 11:52 AM   #3
hgkn
Medlem
 
Join Date: Mar 2003
Location: Kista, Sweden.
Posts: 763
Default

1 Har inte installerat Sp2 i nya datorn. Gör det nu.
2 Har bockat för i driver command men sedan visar den sig inte i kommando raden.
Återkommer när det är uppdaterat (ca 1 dygn)
__________________
hgkn@bahnhof.se
hgkn besöker inte forumet just nu   Reply With Quote
Old 07-26-2010, 09:54 AM   #4
hgkn
Medlem
 
Join Date: Mar 2003
Location: Kista, Sweden.
Posts: 763
Angry

Tillbaks från semester och installerat sp2 till Ts2010.
Har bockat för WaitForTrigger i Driver Command men fårinte fram kommandot sen. Har du någon extra rule för att få det att funka eller??????????
__________________
hgkn@bahnhof.se
hgkn besöker inte forumet just nu   Reply With Quote
Old 07-26-2010, 10:26 AM   #5
korvtiger
Medlem
 
Join Date: Jan 2008
Location: Uppland, Sverige
Posts: 2,728
Default

Inget extra, bara kryssat i i drivercommands och sedan finns den i listan.
Kan du lägga till den i driver-rulen?

Har kollat på Aurans forum, men ingen verkar ha samma problem, men hittade en möjlig lösning.
Gå in i CM3 och sök på category scripts, location local kolla sedan om något script är trasigt, om du hittar ett trasigt, ta bort det.
Kolla dessutom att du inte har dubbletter av WaitForTrigger, eller att den är trasig.

Annars får du fråga på aurans forum under TS2010-tråden.
__________________
-k-
korvtiger besöker inte forumet just nu   Reply With Quote
Old 07-30-2010, 02:50 PM   #6
hgkn
Medlem
 
Join Date: Mar 2003
Location: Kista, Sweden.
Posts: 763
Question

Tycker att jag provat det mesta. Det konstiga är att det fungerar på äldre banor. Skall försöka med fler knep.
__________________
hgkn@bahnhof.se
hgkn besöker inte forumet just nu   Reply With Quote
Old 08-14-2010, 08:30 AM   #7
hgkn
Medlem
 
Join Date: Mar 2003
Location: Kista, Sweden.
Posts: 763
Angry

Får det inte att fungera. SP2 installerat.
WaitForTrigger kuid2:57344:80001:3 är aktiv
WaitForTrigger kuid2:57344:80001:2 är vilande i CM
CM visar följande info. Vilken version har du Korvtiger?
Attached Images
File Type: jpg cm.JPG (27.7 KB, 50 views)
__________________
hgkn@bahnhof.se
hgkn besöker inte forumet just nu   Reply With Quote
Old 08-14-2010, 09:52 AM   #8
korvtiger
Medlem
 
Join Date: Jan 2008
Location: Uppland, Sverige
Posts: 2,728
Default

Jag har endast version 3, WaitForTrigger,<kuid2:57344:80001:3> i min lista, hittar de andra på DLS, men de finns inte i mitt spel. Testa att radera version 2. Brukar aldrig vara bra att ha flera olika versioner av scriptrelaterade saker.
__________________
-k-
korvtiger besöker inte forumet just nu   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump



All times are GMT +2. The time now is 07:59 PM.


Powered by vBulletin® Version 3.7.5
Copyright ©2000 - 2025, Jelsoft Enterprises Ltd.
© Svenska 3D-Tåg 2001-2009