Scenarios för Malmbanan - Svenska 3D-Tåg

Yellow_wing · 2021-03-11, 23:04

@hgv

With scenario: 'Veteran Tag Björkliden-Kiruna' I have a lot of trouble.

I tried multiply time. With long distance scenario, I'm using often the time accelaration (by using EnableAsyncKeys).

I tried with 5x acceleration on the long part of driving. But slow down on any station, signal and so on. The scenario dosn't worked. The train GT42692 didn't move at all and blocked switches and rest of route.

Then I tried with max 2x acceleration the same happends.

So I tried the scenario with normal speed 1x the whole way.

I started on Bjorkliden on 12:28.
In Stordalen I arrived 12:45 on track 2. I had to wait to train GT9912. The train passed on 12:54. But the signal dosn't change to green. I hat to klick manually to the switch. All the times I've got the message 'it is blocked by the train GT9912.
On 12:55 I could change the switch and could drive further in direction Bergfors.

On Bergfors I arrived on 13:26 on track 'station'. Then I could drive about 300 meters to next signal, which was red.
I checked in the 2D menu, I saw the GT42604 still between Kiruna and Krokvik and was NOT moving.
So the scenario ended here, because there where no possibility to get a green signal. The train GT42604 blocked the rest of the scenario.

I checked the scenario in den scenario editor menu. Inside of scenaro edit mode, with the time acceleration function, I was able to observe the full scenario and it worked (as you described earlier).
But in normal drive mode the scenario will not work.

In my opinion instead the AI train will drive such a long way trough this route, it would be better to place more 'Portals' where the AI-trains appear and disappear short to the places, where they should crossing the driver train. But as far as I know, you can only set new Portals in route edit mode and not in scenario edit mode? Because, in scenario edit mode, I couldn't insert a new portal (not in list). In route edit mode, there was the portal object avaiable for insert. But I din't insert it, because after route change may other scenario will may not work anymore?

I sure, you are more expert than I! What you think?

Kind regards
Yellow

2021-03-11, 23:04	#16
Yellow_wing Medlem Reg.datum: Oct 2012 Ort: Switzerland Inlägg: 12	Szenario: Veteran Tag Björkliden-Kiruna @hgv With scenario: 'Veteran Tag Björkliden-Kiruna' I have a lot of trouble. I tried multiply time. With long distance scenario, I'm using often the time accelaration (by using EnableAsyncKeys). I tried with 5x acceleration on the long part of driving. But slow down on any station, signal and so on. The scenario dosn't worked. The train GT42692 didn't move at all and blocked switches and rest of route. Then I tried with max 2x acceleration the same happends. So I tried the scenario with normal speed 1x the whole way. I started on Bjorkliden on 12:28. In Stordalen I arrived 12:45 on track 2. I had to wait to train GT9912. The train passed on 12:54. But the signal dosn't change to green. I hat to klick manually to the switch. All the times I've got the message 'it is blocked by the train GT9912. On 12:55 I could change the switch and could drive further in direction Bergfors. On Bergfors I arrived on 13:26 on track 'station'. Then I could drive about 300 meters to next signal, which was red. I checked in the 2D menu, I saw the GT42604 still between Kiruna and Krokvik and was NOT moving. So the scenario ended here, because there where no possibility to get a green signal. The train GT42604 blocked the rest of the scenario. I checked the scenario in den scenario editor menu. Inside of scenaro edit mode, with the time acceleration function, I was able to observe the full scenario and it worked (as you described earlier). But in normal drive mode the scenario will not work. In my opinion instead the AI train will drive such a long way trough this route, it would be better to place more 'Portals' where the AI-trains appear and disappear short to the places, where they should crossing the driver train. But as far as I know, you can only set new Portals in route edit mode and not in scenario edit mode? Because, in scenario edit mode, I couldn't insert a new portal (not in list). In route edit mode, there was the portal object avaiable for insert. But I din't insert it, because after route change may other scenario will may not work anymore? I sure, you are more expert than I! What you think? Kind regards Yellow